Brushless Motors BLS Series
BL2M425KC-GN+4GN120K+BLSD-K
| Phân loại sản phẩm | Tên sản phẩm | Giá niêm yết | Giá niêm yết | Ngày vận chuyển |
|---|---|---|---|---|
| Motor | BL2M425KC-GN | SGD 151 | USD 121 | 11 Working Days |
| Gearhead | 4GN120K | SGD 96 | USD 77 | 3 Working Days |
| Control Circuit | BLSD-K | SGD 200 | USD 160 | 11 Working Days |
Bao gồm
- motor: None
Gearhead: Mounting Screws, Parallel Key
Control Circuit: None
Thông số kỹ thuật
Đặc trưng
Speed - Torque Characteristics
Kích thước
Motor
Gearhead
Control Circuit
Connection Cable (When Selected)
Flexible Connection Cable (When Selected)
Tải dữ liệu
Các thông số kỹ thuật khác
Common Specifications
| 項目 | BLSD-K､ BLSD-750-C | BLSD-KR | |
|---|---|---|---|
| Operating Data |
Rotation Speed | 25 W､ 40 W､ 90 W: 100–2000 r/min 30 W､ 60 W､ 120 W､ 750 W: 100–4000 r/min The factory default is set to the following rotation speeds. 1500 r/min (when "Function Setting Switch: SPD(SPEED)" is set to "SPD0") 1800 r/min (when "Function Setting Switch: SPD(SPEED)" is set to "SPD1") |
25 W、40 W、90 W: 100–2000 r/min 30 W、60 W、120 W: 100–4000 r/min Factory Default: 0 r/min |
| Acceleration Time and Deceleration Time |
100–30000 ms (Factory Default: 1000 ms) | ||
| Torque Limiting | 0.0–1000.0 % (Factory Default: 1000.0 %) | ||
| Setting Method | Support softwareMEXE02 | RS-485 communication,Support softwareMEXE02 | |
| Input Signal | Input 2 points Photocoupler input method 24 VDC (-15 to +20 %) |
||
| Output Signal | Output 2 points Photocoupler and open-collector output 4.5 to 30 VDC, current less than 10 mA |
||
| Information | When information is generated, the INFO output turns ON and the PWR/SYS LED blinks blue. The motor will continue to operate. |
||
| Alarm | When an alarm occurs, the ALM-B output is turned OFF and the motor stops. At the same time, the PWR/SYS LED blinks red. |
||
| Maximum Extension Distance | BLSD-K､ BLSD-KR: Motor and driver distance 10.5 m (When a sold separately connection cable is used) BLSD750-C: Motor and driver distance 20.5 m [When a sold separately connection cable (For extension) is used] |
||
| Time Rating | Continuous | ||
General Specifications
| Item | Motor | Driver | |
|---|---|---|---|
| Insulation Resistance | After continuous operation at normal ambient temperature and humidity, the measurement value between the coils and the case is 100 MΩ min. using a 500 VDC megger. |
After continuous operation at normal ambient temperature and humidity, the measurement value between the heat sink and the power supply input terminal is 100 MΩ min. using a 500 VDC megger. |
|
| Dielectric Strength | No abnormality is observed even with an application of 0.5 kVAC at 50 Hz between the coils and the case for 1 minute after continuous operation at normal ambient temperature and humidity. |
No abnormality is observed even with an application of 50 Hz, 0.5 kVAC between the heat sink and the power supply input terminal for 1 minute after continuous operation at normal ambient temperature and humidity. |
|
| Temperature Rise | After rated continuous operation at normal ambient temperature and humidity with a heat sink attached*1, the measurement value of the temperature rise on the case surface is 30°C max. (50°C max. for the 90 W type) using the thermocouple method. |
After rated continuous operation at normal ambient temperature and humidity, the measurement value of the temperature rise of the heat sink is 50°C max. using the thermocouple method. |
|
| Operating Environment | Ambient Temperature | 0 to +40°C (Non-freezing) | 0 to +50°C (Non-freezing) *2 |
| Ambient Humidity | 85% max. (Non-condensing) | ||
| Altitude | Up to 1000 m above sea level | ||
| Atmosphere | No corrosive gases or dust. Should not be exposed to water or oil. Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments. |
||
| Vibration | Must not be subjected to continuous vibration or excessive shock. Conforms to JIS C 60068-2-6, "Sine-Wave Vibration Test Method." Frequency Range: 10 to 55 Hz, Half Amplitude: 0.15 mm Sweep Direction: 3 directions (X, Y, Z), Number of Sweeps: 20 times |
||
| Storage Conditions*3 | Ambient Temperature | -25 to +70°C (Non-freezing) | |
| Ambient Humidity | 85% max. (Non-condensing) | ||
| Altitude | Up to 3000 m above sea level | ||
| Atmosphere | No corrosive gases or dust. Should not be exposed to water or oil. Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments. |
||
| Thermal Class | UL/CSA Standards: 105 (A), EN Standards: 120 (E) | − | |
| Degree of Protection*5 | 25 W, 40 W, 90 W: IP40 (Excluding the installation surface and connectors) 30 W, 60 W, 120 W: IP65 (Excluding the installation surface and connectors) |
IP20 | |
- *1
- The size of the heat sink (Material: Aluminum) is as follows.
30 W Type: 115 × 115 mm, thickness 5 mm, 25 W, 60 W Type: 135 × 135 mm, thickness 5 mm, 40 W, 90 W, 120 W Type: 200 × 200 mm, thickness 5 mm
The round shaft type should be mounted on a heat sink to keep the motor case surface temperature below 90°C. - *2
- When drivers are installed in a close contact state, operate at an ambient temperature of 0 to +40°C.
- *3
- The value for storage condition applies to short periods such as the period during transport.
Note
- Do not measure insulation resistance or perform a dielectric strength test while the motor and driver are connected.
Permissible Radial Load and Permissible Axial Load
| Output Power | Gear Ratio | Permissible Radial Load N | Permissible Axial Load N |
|
|---|---|---|---|---|
| From the end of the output shaft 10mm |
From the end of the output shaft 20mm |
|||
| 25 W | 3～18 | 100 | 150 | 50 |
| 25～180 | 200 | 300 | ||
| 40 W | 3～18 | 250 | 350 | 100 |
| 25～180 | 300 | 450 | ||
| 90 W | 3～9 | 400 | 500 | 150 |
| 12.5～18 | 450 | 600 | ||
| 25～180 | 500 | 700 | ||
Load position
Tiêu chuẩn
Speed - Torque Characteristics
Regulations and Standards Materials
Documents about compliance with regulations and standards can be downloaded from the "Data Download" tab on the product details page.
(The types of files available for download vary by product.)
Explanations of the Global Laws, Regulations and Standards can be found here.
Information about our compliance with safety standards for each of our product models can be found here.
Hazardous Substances
The product does not contain any substances (10 substances) exceeding the regulation values of the RoHS Directive (2011/65/EU, 2015/863/EU).
Cấu hình hệ thống
Cáp và phụ kiện
close
close
close
close