Brushless Motors
BMU Series
- Equipped with a Digital Display Panel and a Setting Dial, It is Easy to Operate with a Rotate-and-Push
- Equipped with Features such as Load Factor Display, 4-Speed Operation and Alarm Output
- Easy Wiring to Connect the Motor and Driver
- Output Power 30 to 400 W
- Speed Control Range 80 to 4000 r/min
Tính năng |Brushless motor BMU Series
Key Features
Maximum Rotation Speed 4000 r/min, Speed Ratio 1:50 (2.5 times higher than conventional products)
The BMU Series has a maximum speed of 4000 r/min. A speed ratio of 1:50 (80~4000 r/min) is achieved. Speed regulation has also been greatly improved from ±0.5 % to ±0.2 % of conventional products.
Advantages of Brushless Motors
The brushless motor achieves high efficiency by employing permanent magnets in the rotor section.
The energy saving motors reduce power consumption and CO2 emissions.
Furthermore, the small size and light weight of the motor helps conserve resources and contributes to carbon neutrality initiatives.
Full Functionality
-
Speed Display
Displays the motor rotation speed in increments of 1 r/min. Calculate the conveyor gear ratio and set the "Gear Ratio" parameter to display the conveyor transfer speed in m/s.
-
Load Factor Display
With the rated torque of the motor at 100 %, the load factor can be displayed as a percentage (40~200 %).
The load condition during start-up, as well as the load condition due to the aging deterioration of the equipment, can be confirmed. -
Protective Function
Equipped with various protective functions, such as the overload protective function and the overvoltage protective function.
When any protective function is activated, the alarm code is shown on the display and the alarm signal is output.
4-Speed Operation
4-speed operation is possible by setting the data to operation data No. 0, No. 1, No. 2, or No. 3, and switching the input of the M0 and M1 terminals.
Note
When operating in 4-speed settings, the rotation direction of the motor cannot be changed by external input signals.
(30, 60, 120 W)
Setting the Acceleration/Deceleration Time
The setting for the acceleration time and deceleration time can be adjusted with the acceleration/deceleration time potentiometer, or can be done via the digital setting.
- Setting Range: 0.0~15.0 sec (Initial value: 0.5 sec)
Fine adjustment of the shock mitigation is possible when starting and stopping the load, and the time can be freely set to match the takt time.
Output Shaft Holding When Stopped
The load can be electrically held when the motor is at standstill. (Holding force of approximately 50 % of the rated torque)
Note
If the power supply to the driver is turned OFF, the holding force dissipates. This cannot be used to prevent a fall during a power outage.
Other Functions
- Setting Dial Operations Lock
- When operating by an external signal, operation of the switch on the front panel can be set to "Invalid".
Connector Type Direct Connection
Locking Lever Type Connector for Direct Connection (Connector type)
A locking lever type connector specifically designed for small motors allows direct connection between motor and driver.
Simple Connection
Cable connection is easy due to the locking lever that does not require screw fitting.
Installation Method
- Insert the connector
- Turn down the locking lever
- Connection Completed
Direct Connection With Motors and Drivers*
Without an extension cable, a connection of up to 10 m is possible.
Flexible cables are also available
Use the flexible connection cable in applications where the cable is bent and flexed repeatedly.
- *For the connector type, watertight, dust-resistant connection cables are available for relay connection.
Cable Outlet Direction Can be Selected
IP67 Watertight, Dust-Resistant Motor That Can be Washed in Water
Features of Watertight, Dust-Resistant Motors
Excellent Protective Structure, Degree of Protection
-
Motor Structure
A sealing insert (O-ring) is used for the mating part to prevent water from entering the inside of the motor.
-
Connector Structure
The connector structure has a built-in gasket and O-ring for improved waterproofing.
It is IP67-compliant, including the connector part.
Water-Washable IP67 Rating
Can be washed with water while still attached to the equipment
Usable in dusty applications
- Waterproof Test Conditions:
- Immersion to a depth of 1 m for 30 minutes
"Water-Washing Resistant Test" Which Takes Into Account Deterioration Over Time Individual Company Evaluation
Oriental Motor's Original "Water-Washing Resistant Test"*
- ① Thermal Shock Test
- Apply heat deterioration equivalent to 5 years for sealing insert (O-ring)
- ② Vibration Test
- Apply vibration to the motor
- ③ Water Jet Test
- Apply water pressure of 100 kPa.
- *Refer to here for details on test conditions.
Improved Anti-Corrosion Properties
Special rust-resistant coating is applied, and stainless steel material is used for the output shaft and screws. The mounting surface is also painted to prevent rusting, even when assembled to stainless steel equipment.
Matches a Clean Environment
No cooling fan needed, because of the high efficiency motor. Therefore, there is no need to worry about generating dust from outside.
New Connection Cable With IP66/IP67 Rating (For connector type)
Watertight, dust-resistant connection cable for relay connection of motors and drivers are now available.
The connector of the relay section is IP66/IP67-compliant
- For more details about the products, please contact your nearest branch or sales office or Customer Support Center.
A Wide Variety of Gearheads to Choose From
In addition to the conventional parallel shaft gearhead GFV gearheads, a lineup of gearheads with features such as high gear ratio, high strength, and space saving is available.
The permissible load and maximum permissible torque of the output shaft have been greatly increased.
Gearhead Types and Features
Gearhead Type | Parallel Shaft Gearhead | Right-Angle Gearhead | Hollow Shaft Flat Gearhead | ||
---|---|---|---|---|---|
GFV Gearhead | JV Gearhead | JB Gearhead | JH Gearhead | FR Gearhead | |
External View | |||||
Features |
|
|
|
|
|
Output Power | 30 W, 60 W, 120 W 200 W, 300 W, 400 W |
200 W, 300 W, 400 W | 200 W, 300 W, 400 W | 60 W, 120 W, 200 W 300 W, 400 W |
30 W, 60 W, 120 W 200 W, 300 W, 400 W |
Gear Ratio | 5~200 | 100~450 | 5~1200 | 5~200 | 5~200 |
Rated Life | 10000 hours | 5000 hours | 5000 hours | 5000 hours | 10000 hours |
Permissible Radial Load* | 1400 N | 3123 N | 3672 N | 2405 N | 2040 N |
Permissible Axial Load* | 400 N | 480 N | 577 N | 550 N | 800 N |
Permissible Torque* | 70 N·m | 198 N·m | 518 N·m | 82.8 N·m | 54 N·m |
- *This value is for output power of 200 W, 3000 r/min, and the maximum gear ratio.
Related Products
AC Speed Control Motors
US2 Series
- Easy "rotate-and-push" operation
- Equipped with a display panel and a setting dial
- Easy setting and easy wiring
- 6~90 W, 90~1400 (1600) r/min
Brushless Motors
BLE2 Series
- Multifunctional model with 4 selectable data setting methods
- Torque limited, 16-speed operation
- For the type with an electromagnetic brake, it can hold the load during vertical operation
- 30~400 W, 80~4000 r/min
Stepper Motors
PKP Series/CVD Series SC Type Driver
- Easy control with forward/reverse input
- two-speed operation
- 0.02~600 r/min
Thu hẹp phạm vi sản phẩm