Brushless Motors BLV Series R Type

BLVD-KRD

In tất cả thông tin sản phẩm cùng một lúc
BLVD-KRD

Control Circuit

Power Supply Cable (Control Circuit～Power Supply)

Phân loại sản phẩm Tên sản phẩm Giá niêm yết Giá niêm yết Ngày vận chuyển
Control Circuit BLVD-KRD SGD 473 USD 378 3 Working Days
• This product is a brushless motor driver only. A combination of motor and connection cable is required for driving.

Bao gồm

  • Control Circuit: None

Thông số kỹ thuật

Kích thước

Control Circuit
Control Circuit

Control Circuit

Power Supply Cable (When selected)
Power Supply Cable (When selected)

Power Supply Cable (When selected)

Tải dữ liệu

Các thông số kỹ thuật khác

Common Specifications

Item Specifications
Input Signals 4 points, Photocoupler input method
Output Signals 2 points, Photocoupler and open-collector output
Main Operation Functions Continuous operation, positioning operation, JOG operation, return-to-home operation
Operation Data Setting Number 256 Points
Setting Tool Support Software MEXE02
Maximum Extension Distance Distance between motor and driver: 3.5 m* (when a connection cable (sold separately) is used)
  • * 60 W type is 3.0 m.

Communication Specifications

Power supply for communication*

Power supply current capacity Input power supply voltage
0.2 A or more DC24-48 V
  • * For the 24 VDC 400 W type, a power supply for communication is not required.
  • 　

RS-485 Communication Specifications

Electrical Characteristics EIA-485 compliant
Using twisted-pair wires, the total extension distance of the communication cable should be no more than 10 m. *
communication mode Half duplex
Asynchronous mode (Data: 8-bits, Stop bit: 1-bit/2-bits, Parity: none/even/odd)
Transmission Rate Select from 9,600 bps, 19,200 bps, 38,400 bps, 57,600 bps, 115,200 bps, 230,400 bps (initial value)
Protocol Modbus RTU Mode
Connection Type A maximum of 31 units can be connected to a single host controller.
  • 　
  • * If a specific wiring and layout causes the motor cable or power supply cable to generate a noise problem, shield the cable or use ferrite cores.
  • 　

CANopen Communication Specifications

Electrical Characteristics ISO 11898 compliant
Please use a CAN-BUS cable.
Communication Protocol CANopen
Communication Profile Compliant with CiA DS301 Version 4.2.0
Device Profile CiA DSP402 Version 4.0.0 compliant
Node ID 1~127
Bit Rate Select from 1 Mbps, 800 kbps, 500 kbps (initial value), 250 kbps, 125 kbps, 50 kbps, 20 kbps, 10 kbps
Maximum Bus Length 25 m (maximum bus length at 1 Mbps)
Communication Object NMT (Network Management)
SDO (Service Data Object: 1 SDO server)
PDO (Process Data Object: 4 Receive-PDO, 4 Transmit-PDO)
EMCY (Emergency Object)
SYNC(Synchronization Object)
Modes of operation Profile velocity mode (pv)
Profile position mode (pp)
Homing mode (hm)

General Specifications

Item Motor Driver
Insulation Resistance 100 MΩ or more when a 500 VDC megger is applied between the windings and the case after continuous operation*1 under normal ambient temperature and humidity.
 		 After continuous operation under normal ambient temperature and humidity, the measurement value between the power supply input and the heat sink is min. 100 MΩ using a 500 VDC megger.
 
Dielectric Strength After continuous operation*1 at normal ambient temperature and humidity, no abnormality is observed even when 50 Hz, 0.5 kVAC is applied between the windings and the case for 1 minute.
 		 After continuous operation at normal ambient temperature and humidity, no abnormality is observed even when 50 Hz, 0.5 kVAC is applied between the power supply input and the heat sink for 1 minute.
 
Temperature Rise After rated continuous operation*1 at normal ambient temperature and humidity,
the measured value using the thermocouple method is 60 °Cmax.
for the temperature rise of the coils and 50 °C max. 50 °C*2. for the temperature rise on the case surface.		 After rated continuous operation at normal ambient temperature and humidity,
the measurement value of the temperature rise of the heat sink is 50 °C max. using the thermocouple method.
Operating Environment Ambient Temperature 0~+40 °C (Non-freezing) 0~+40 °C (Non-freezing)*3
Ambient Humidity 85 % max. (Non-condensing)
Altitude Less than 1000 m above sea level
Atmosphere No corrosive gases or dust Should not be exposed to water or oil.
Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments.
Vibration Not subject to continuous vibration or excessive shock In conformance with JIS C 60068-2-6, "Sine-wave vibration test method" Frequency range: 10~55 Hz,
Single amplitude: 0.15 mm Sweep direction: 3 directions (X, Y, Z) Number of sweeps: 20
Storage Conditions *4 Ambient Temperature -20~+70 °C (non-freezing) -25~+70 °C (non-freezing)
Ambient Humidity 85 % max. (Non-condensing)
Altitude Less than 3000 m above sea level
Atmosphere No corrosive gases or dust Should not be exposed to water or oil.
Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments.
Thermal Class UL/CSA Standards: 105 (A), EN Standards: 120 (E) −
Degree of Protection IP40 IP20
*1
The 400 W type has a 30 minutes rating.
*2
For round shaft types, attach to a heat sink (Material: aluminum) of one of the following sizes to maintain a motor case surface temperature of 90 °C max.
60 W type: 135 × 135 mm 5 mm thick
100 W type: 165 × 165 mm 5 mm thick
200 W type: 200 × 200 mm 5 mm thick
400 W type: 250 × 250 mm 6 mm thick
*3
Install the driver to a location that has the same heat radiation capability as an aluminum metal plate.
BLVD-KRD: 200 x 200 mm 2 mm thick,BLVD-KBRD: 350 x 350 mm 2 mm thick
*4
The value for storage condition applies to short periods such as the period during transport.
Note
  • Do not measure insulation resistance or perform a dielectric strength test the motor and driver are connected.

Tiêu chuẩn

Regulations and Standards Materials

Documents about compliance with regulations and standards can be downloaded from the "Data Download" tab on the product details page.
(The types of files available for download vary by product.)

Explanations of the Global Laws, Regulations and Standards can be found here.

Information about our compliance with safety standards for each of our product models can be found here.

Hazardous Substances

The product does not contain any substances (10 substances) exceeding the regulation values of the RoHS Directive (2011/65/EU, 2015/863/EU).

Tải dữ liệu
In tất cả thông tin sản phẩm cùng một lúc
close
close
close
close