Brushless Motors BLV Series R Type
BLMR6200SK-GFV-B
Motor
| Phân loại sản phẩm | Tên sản phẩm | Giá niêm yết | Giá niêm yết | Ngày vận chuyển |
|---|---|---|---|---|
| Motor | BLMR6200SK-GFV-B | SGD 364 | USD 291 | 3 Working Days |
Bao gồm
- Motor: None
Thông số kỹ thuật
Tải dữ liệu
Các thông số kỹ thuật khác
General Specifications
| Item | Motor | Driver | |
|---|---|---|---|
| Insulation Resistance | 100 MΩ or more when a 500 VDC megger is applied between the windings and the case after continuous operation*1 under normal ambient temperature and humidity. |
After continuous operation under normal ambient temperature and humidity, the measurement value between the power supply input and the heat sink is min. 100 MΩ using a 500 VDC megger. |
|
| Dielectric Strength | After continuous operation*1 at normal ambient temperature and humidity, no abnormality is observed even when 50 Hz, 0.5 kVAC is applied between the windings and the case for 1 minute. |
After continuous operation at normal ambient temperature and humidity, no abnormality is observed even when 50 Hz, 0.5 kVAC is applied between the power supply input and the heat sink for 1 minute. |
|
| Temperature Rise | After rated continuous operation*1 at normal ambient temperature and humidity, the measured value using the thermocouple method is 60 °Cmax. for the temperature rise of the coils and 50 °C max. 50 °C*2. for the temperature rise on the case surface. |
After rated continuous operation at normal ambient temperature and humidity, the measurement value of the temperature rise of the heat sink is 50 °C max. using the thermocouple method. |
|
| Operating Environment | Ambient Temperature | 0~+40 °C (Non-freezing) | 0~+40 °C (Non-freezing)*3 |
| Ambient Humidity | 85 % max. (Non-condensing) | ||
| Altitude | Less than 1000 m above sea level | ||
| Atmosphere | No corrosive gases or dust Should not be exposed to water or oil. Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments. |
||
| Vibration | Not subject to continuous vibration or excessive shock In conformance with JIS C 60068-2-6, "Sine-wave vibration test method" Frequency range: 10~55 Hz, Single amplitude: 0.15 mm Sweep direction: 3 directions (X, Y, Z) Number of sweeps: 20 |
||
| Storage Conditions *4 | Ambient Temperature | -20~+70 °C (non-freezing) | -25~+70 °C (non-freezing) |
| Ambient Humidity | 85 % max. (Non-condensing) | ||
| Altitude | Less than 3000 m above sea level | ||
| Atmosphere | No corrosive gases or dust Should not be exposed to water or oil. Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments. |
||
| Thermal Class | UL/CSA Standards: 105 (A), EN Standards: 120 (E) | − | |
| Degree of Protection | IP40 | IP20 | |
- *1
- The 400 W type has a 30 minutes rating.
- *2
-
For round shaft types, attach to a heat sink (Material: aluminum) of one of the following sizes to maintain a motor case surface temperature of 90 °C max.
60 W type: 135 × 135 mm 5 mm thick
100 W type: 165 × 165 mm 5 mm thick
200 W type: 200 × 200 mm 5 mm thick
400 W type: 250 × 250 mm 6 mm thick - *3
- Install the driver to a location that has the same heat radiation capability as an aluminum metal plate.
BLVD-KRD: 200 x 200 mm 2 mm thick,BLVD-KBRD: 350 x 350 mm 2 mm thick - *4
- The value for storage condition applies to short periods such as the period during transport.
- Do not measure insulation resistance or perform a dielectric strength test the motor and driver are connected.
Tiêu chuẩn
Regulations and Standards Materials
Documents about compliance with regulations and standards can be downloaded from the "Data Download" tab on the product details page.
(The types of files available for download vary by product.)
Explanations of the Global Laws, Regulations and Standards can be found here.
Information about our compliance with safety standards for each of our product models can be found here.
Hazardous Substances
The product does not contain any substances (10 substances) exceeding the regulation values of the RoHS Directive (2011/65/EU, 2015/863/EU).
close
close